# $Id: pnpdump.c,v 1.15a 1998/05/25 17:22:16
fox Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER
#
# Trying port address 0203
# Board 1 has serial identifier 8d 01 00 01 00 01 00 a9 0d
# Board 2 has serial identifier 70 00 05 25 10 84 20 b0 4e
# (DEBUG)
(READPORT 0x0203)
(ISOLATE CLEAR)
(VERIFYLD N)
(IDENTIFY *)
# Card 1: (serial identifier
8d 01 00 01 00 01 00 a9 0d)
# Vendor Id CMI0001, Serial Number 16777472, checksum 0x8D.
# Version 1.0, Vendor version 0.0
# ANSI string -->CMI8330. Audio Adapter<--
#
# Logical device id @@@0001
#
# Edit the entries below to uncomment out the configuration
required.
# Note that only the first value of any range is given, this
may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CMI0001/16777472
(LD 0
# Multiple choice time,
choose one only !
# Start dependent functions:
priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0530
# Maximum IO base address 0x0530
# IO base alignment 1 bytes
# Number of IO addresses required: 8
(IO 0 (BASE 0x0530))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 8
(IO 1 (BASE 0x0388))
# IRQ 11.
# High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 11 (MODE +E)))
# First DMA channel 0.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
(DMA 0 (CHANNEL 0))
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0530
# Maximum IO base address 0x0530
# IO base alignment 1 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0530))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 8
# (IO 1 (BASE 0x0388))
# IRQ 5, 7, 9, 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0e80
# Maximum IO base address 0x0f40
# IO base alignment 192 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0e80))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x03f8
# IO base alignment 16 bytes
# Number of IO addresses required: 8
# (IO 1 (BASE 0x0388))
# IRQ 5, 7, 9, 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# End dependent functions
(ACT Y)
))
#
# Logical device id @H@0001
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3d
#
# Edit the entries below to uncomment out the configuration
required.
# Note that only the first value of any range is given, this
may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CMI0001/16777472
(LD 1
# Multiple choice time,
choose one only !
# Start dependent functions:
priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0330
# IO base alignment 1 bytes
# Number of IO addresses required: 2
(IO 0 (BASE 0x0330))
# IRQ 9.
# High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 9 (MODE +E)))
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 16 bytes
# Number of IO addresses required: 2
# (IO 0 (BASE 0x0300))
# IRQ 5, 7, 9, 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# End dependent functions
(ACT Y)
))
#
# Logical device id @P@0001
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3d
#
# Edit the entries below to uncomment out the configuration
required.
# Note that only the first value of any range is given, this
may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CMI0001/16777472
(LD 2
# Multiple choice time,
choose one only !
# Start dependent functions:
priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0200
# IO base alignment 1 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0200))
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0fe0
# IO base alignment 16 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0200))
# End dependent functions
# (ACT Y)
))
#
# Logical device id @X@0001
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3d
#
# Edit the entries below to uncomment out the configuration
required.
# Note that only the first value of any range is given, this
may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CMI0001/16777472
(LD 3
# Multiple choice time,
choose one only !
# Start dependent functions:
priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0220
# IO base alignment 1 bytes
# Number of IO addresses required: 16
(IO 0 (BASE 0x0220))
# IRQ 5.
# High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
(DMA 0 (CHANNEL 1))
# Next DMA channel 5.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
(DMA 1 (CHANNEL 5))
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0240
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# IRQ 5, 7, 9 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 5 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# IRQ 5, 7, 9, 10, 11 or 12.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 5 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# End dependent functions
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Card 2: (serial identifier
70 00 05 25 10 84 20 b0 4e)
# Vendor Id SUP2084, Serial Number 337168, checksum 0x70.
# Version 1.0, Vendor version 0.0
# ANSI string -->SupraExpress 56i Sp<--
#
# Logical device id SUP2084
# Device support I/O range check register
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3d
#
# Edit the entries below to uncomment out the configuration
required.
# Note that only the first value of any range is given, this
may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE SUP2084/337168
(LD 4
# Compatible device id SUP2080
# Multiple choice time,
choose one only !
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03f8
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x03f8))
# IRQ 4.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 4 (MODE +E)))
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02f8
# Maximum IO base address 0x02f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x02f8))
# IRQ 3.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03e8
# Maximum IO base address 0x03e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x03e8))
# IRQ 4.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 4 (MODE +E)))
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02e8
# Maximum IO base address 0x02e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x02e8))
# IRQ 3.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03e8
# Maximum IO base address 0x03e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x03e8))
# IRQ 5.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02e8
# Maximum IO base address 0x02e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x02e8))
# IRQ 5.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03e8
# Maximum IO base address 0x03e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
(IO 0 (BASE 0x03e8))
# IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
# High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 7 (MODE +E)))
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02e8
# Maximum IO base address 0x02e8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x02e8))
# IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03f8
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x03f8))
# IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x02f8
# Maximum IO base address 0x02f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x02f8))
# IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Start dependent functions:
priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0200))
# IRQ 3, 4, 5, 7, 10, 11, 12 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# End dependent functions
(ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to
the "Wait for Key" state
(WAITFORKEY)
|
